難切削材料切削時切削液的選用：常用的切削液有水溶液、普通乳化液、極壓乳化液、礦物油、復合（植物、礦物、動物）油、極壓切削油。在它們中，水溶液冷卻效果最好，極壓切削液的潤滑效果最好。一般的切削液在200℃左右就失去潤滑能力，可是在切削液中添加極壓添加劑（如氯化石蠟、四氯化碳、硫代磷酸鹽、二烷基二硫代磷酸鋅等）就成為潤滑良好的極壓切削液，就可在600～1000℃高溫和1470～1960Mpa高壓條件下...

隨著時代的進步，我們也必須跟上步伐了，在如今的生產行業，如果你沒有一臺數控全自動攻絲機的話，那么你就別想指望能跟上時代的步伐！想要擁有該設備，那么你就得找到個數控全自動攻絲機廠家！不過也有些使用該設備的朋友，買了設備用著什么問題都沒有的，但是有些地方他不能理解，比如說；“為什么開啟的時候是反轉，但是攻絲時吃上力了就變成正轉了，而且向上退的時候又能夠反轉過來”；類似的問題，在這給大家普及下這方面的知...

攻牙機多軸器的應用領域攻牙機多軸器廣泛應用于機械行業多孔零部件的鉆孔及攻絲加工。如汽車、摩托車多孔零部件：發動機箱體、鋁鑄件殼體、制動鼓、剎車盤、轉向器、輪轂、差速殼、軸頭、半軸、車橋等，泵類、閥類、液壓元件、太陽能配件等等。多孔鉆在其加工范圍內，其主軸的數量、主軸間的距離，可以任意調整，一次進給同時加工數孔。在其配合液壓機床工作時，可自動進行快進、工進(工退)、快退、停止、同單軸鉆(攻絲)比較，...

鉆孔攻牙復合機的功能1、程序控制采用PLC可編程控制器，人機界面采用觸摸屏顯示操作，人機友好對話，操作簡便。2、適合大、中批量零件加工，多方向同時鉆、攻、銑，一次性裝夾完成，可自動退料，效率高，一人可操作幾臺，精度好。3、攻牙采用將軍牌齒輪牙距式自動攻牙機，鉆孔采用臺灣胡氏動力頭。4、鉆孔可用油壓或空壓，由工件鉆孔大小來確定。5、攻牙可以自動吹鐵削功能，自動加攻牙油

絲攻材質的好壞，種類之間的差異，下孔形狀大小等等條件都會影響自動攻牙機攻絲速度。因此在選購自動攻牙機的時候一定要考慮到上述因素。自動攻牙機由于其速度快、精度高，攻出來的牙優質，可以通過正規牙規檢測而深受企業的親睞。然而仍然存在三大要素影響攻絲速度。擠壓絲錐在自動攻牙機中因沒有切屑的困擾，攻牙速度可以比切削的快，同時也要考慮到被加工材料、切削液、機械等因素，一般大都采用在5-20m/MIN中，與沖床...

攻牙機出現的問題：爛牙出現原因分析：1、底孔太小，螺絲攻攻不進，孔口爛牙2、頭攻、二攻不重合3、螺孔攻歪很多，用螺絲攻硬借，但借不過來4、對低碳鋼等塑性好的材料，未加潤滑冷卻液，螺絲攻把工件上螺紋粘去一塊又一塊，尤其是在攻細牙螺紋的時候5、機攻鋁件時如螺絲攻擺動，或切削刃磨得很不對稱經及沒及時排除切屑防止方法：1、檢查底孔直徑，把孔擴大后再攻絲2、用二攻攻絲時，必須先用手把二攻前端旋入螺孔后再攻絲...

全自動鉆孔機根據設定的程序或是指令，自行完成整個操作流程，在很大程度上提高了工程質量和效率，是一種自動化程度較高的自動化專機。本公司專業生產全自動攻牙機、全自動鉆孔機、全自動倒角機、全自動開槽機、自動開料機、多軸器和振動盤等自動化設備、制造多軸攻牙機、鉆孔攻牙組合機、承接非標準自動化機械設計、使原本復雜繁鎖的工序簡單化、自動化、高效化，為勞動密集型生產企業節約了大量的人力、物力。說說全自動鉆孔機的...

砂輪是攻牙機在磨削時使用的切削刀具，它是由磨粒和結合劑構成的多孔物體.砂輪的磨粒。主要有剛玉和碳化硅兩大類剛玉的韌性較大，適宜于磨削鋼材等韌性材料。碳化硅的性能較剛玉硬且脆，適用于磨削硬質合金和鑄鐵等脆性材料，在粗磨時一般應選用磨粒粗大的砂輪，精磨時則應使用磨粒細小的砂輪。砂輪的結合劑有陶瓷、樹脂和橡膠三大類陶瓷為無機材料，耐腐蝕，價格便宜。但是陶瓷材料性脆，不適合制造薄型砂輪。樹脂結合劑制成的砂...

攻牙機是一種在機件殼體、設備端面、螺母、法蘭盤等各種具有不同規格的通孔或盲孔的零件的孔的內側面加工出內螺紋、螺絲或叫牙扣的機械加工設備。攻牙機在制造業的生產中起到了重要的作用。攻牙機的優勢：減少工序,提高自動化程度。模內攻牙機將需攻絲零件沖壓與攻牙動作結合一體,直接在沖床上攻牙與沖壓同步進行。安裝簡單更換方便：模內攻牙機設計堅固耐用,體積小,易安裝于不同模具內,攻牙頭可更換不同規格。標準的精確螺紋...

模內攻牙機的優點：1.實現全自動化沖壓攻牙加工生產；2.節省電力,人工，搬運，防止漏攻；3.采用無屑擠壓絲錐攻牙，螺紋強度好,精度高，絲錐壽命長；4.更換不同規格的導程組件，在同一臺機身上可以成型不同的螺紋尺寸；5.人性化的機身設計，體積小，易安裝固定在模具內使用；6.提高生產效率，適合精密要求高，數量大的訂單。交期可準確掌控；7.實現快速互換于不同的模具，適合種類多訂單少的生產；8.采用雙保險的...